Autel ADAS Calibration Set — Package 3 (Without Scan Tool)

The Autel ADAS Calibration Set Package 3 (SKU: AUADASCOMPLETE) is Autel's complete static ADAS calibration frame and target system, sold without a diagnostic tablet — the right configuration for shops that already own a MaxiSYS Ultra, MS909, MS919, or Elite II and need the hardware side of the ADAS equation. If your shop is doing windshield replacements, front-end repairs, or camera and radar R&R, this is the calibration rig that makes that work billable and documentable.

What ADAS Calibration Is and Why Shops Need It

Modern vehicles require recalibration of forward-facing cameras, adaptive cruise control radar, blind-spot monitors, surround-view systems, and night vision sensors any time a windshield is replaced, a front-end component is disturbed, or suspension geometry changes. Without calibration, those systems either throw codes or — worse — operate with degraded accuracy that the driver doesn't notice until something goes wrong. Liability falls on whoever touched the vehicle last.

Autel supports both static calibration (target-based, performed in the shop) and dynamic calibration (road-drive procedure). Package 3 is built around the static target workflow, which is what most shops run for the majority of procedures.

What's Included in Package 3

• CSC (Calibration Standard Component) Frame — Autel's vehicle-positioning calibration frame, adjustable for height and width to accommodate passenger cars through light commercial vehicles
• Full target panel set — vehicle-specific calibration targets for front cameras, radar, night vision, and AVM (surround-view) procedures
• Calibration accessories kit — alignment rulers, positioning guides, and all hardware required to set up the frame correctly per vehicle
• Carry and storage cases — targets and frame components ship in protective cases; same cases are used for storage between jobs

Note: This package does NOT include a MaxiSYS diagnostic tablet. If you need the tablet bundled in, contact us — we can configure a package with the MS909, MS919, or Ultra depending on your workflow. If you already own one of those tablets with ADAS software licensing, Package 3 is exactly what you need.

Compatible Autel Tablets

Package 3 pairs with any of the following MaxiSYS tablets running Autel ADAS software:

• MaxiSYS Ultra — top-tier tablet with integrated oscilloscope and full OE-level diagnostics
• MaxiSYS MS919 — mid-to-high tier with integrated scope
• MaxiSYS MS909 — full diagnostics without integrated scope; most common ADAS pairing in independent shops
• MaxiSYS Elite II — previous-generation platform, still fully supported for ADAS procedures

If your tablet has the ADAS software subscription active, it will drive the entire calibration workflow — vehicle selection, target positioning instructions, live camera feed during alignment, pass/fail confirmation, and printed calibration report.

What Systems This Rig Calibrates

• Forward-facing cameras — lane departure warning (LDW), lane keep assist (LKA), forward collision warning (FCW), automatic emergency braking (AEB)
• Adaptive cruise control radar — front radar units, both long-range and mid-range
• Night vision systems — infrared camera calibration where supported by the vehicle OEM
• Surround-view / AVM systems — 360-degree camera calibration requiring all four cameras to be adjusted to a unified reference plane
• Blind-spot monitoring — rear and side radar calibration on supported platforms

Which Shop Is This Configuration For?

Package 3 at $12,858.75 is built for shops that have already committed to Autel diagnostics and want to add ADAS calibration as a revenue service without buying a second tablet:

• Independent repair shops already running MS909 or MS919 for diagnostics who are turning away ADAS jobs or subbing them out
• Auto glass specialists who need in-house calibration capability after windshield installs — the CSC frame handles the static procedures most glass shops run daily
• Collision repair centers where the diagnostic tablet is already on the floor and ADAS calibration is the missing piece
• Multi-bay shops that want a dedicated ADAS station separate from the diagnostic bay

If you don't own an Autel MaxiSYS tablet yet, we have bundles that include the MS909 or MS919 — call us and we'll spec out the right configuration for your volume and vehicle mix.

Space and Setup Requirements

Static ADAS calibration requires a level floor area with adequate clearance in front of the vehicle for the target frame. Exact vehicle-to-target distances vary by make, model, and the specific system being calibrated — the Autel software provides step-by-step positioning instructions for each procedure. If you're not sure your shop floor will work, contact us before ordering and we can walk through the requirements with you.

Why Buy From OEM Diagnostic Tools?

• Authorized Autel dealer since 2016 — we know the product line and can give you honest guidance on which configuration fits your shop
• Free ground shipping on this order
• Free tech support at 866-217-0063 — staffed by people who understand ADAS calibration workflows, not a general call center
• Full manufacturer warranty on every component in this package
• Honest upgrade guidance — if Package 3 isn't the right fit, we'll tell you before you order, not after

Call 866-217-0063 for quick answers and help!